The standards and parameters listed in the technical data sheets (specs) for plastic raw materials determine the material’s processability, mechanical strength, thermal performance, and response to environmental conditions.
1. Detailed Explanations of Key Terms in Raw Material Specifications
- Melt Flow Index (MFI) (ASTM D1238 – ISO 1133)
- Explanation: Indicates the amount of molten plastic, in grams, that flows through a calibrated orifice in 10 minutes under a specific temperature and load (e.g., for PE).
- Importance: It indicates the material’s flowability. A low MFI indicates high molecular weight and strength (ideal for extrusion and thick-wall part production); a high MFI ensures easy flow and is preferred in injection molding, which requires thin walls and fast cycle times.
- Density (ASTM D792 – ISO 1183)
- Description: It is the mass per unit volume of a material ( ).
- Importance: It directly affects part weight, raw material cost, and the material’s degree of crystallinity (e.g., HDPE vs. LDPE). It provides insight into sink/float properties and filler content ratios.
- Tensile Stress (Yield) / Yield Strength (ASTM D638 – ISO 527-2)
- Description: The stress value at which a material begins to undergo permanent (plastic) deformation ( or ).
- Importance: It indicates the maximum tensile force a material can withstand before deforming under load. A high yield strength ensures that the material remains rigid under load.
- Tensile Strain (Break) / Elongation at Break (ASTM D638 – ISO 527-2)
- Description: It expresses, as a percentage (%), how much the material’s length can increase before it breaks.
- Importance: Indicates the material’s ductility (flexibility) or brittleness. High elongation at break indicates that the material will flex rather than break easily under impact or bending.
- Flexural Modulus (ASTM D790)
- Description: This value indicates a material’s resistance to bending—that is, its stiffness (modulus of elasticity) ( or ).
- Importance: Materials with a high flexural modulus (especially those reinforced with glass fiber) are resistant to bending; this is critical in applications where deflection under load is undesirable.
- Notched Izod Impact Strength (23°C and -10°C) (ASTM D256 – ISO 179/1eA)
- Description: The amount of energy absorbed when a notched specimen is fractured by a pendulum impact ( or ).
- Importance: It measures the material’s resistance to sudden impacts. The value at room temperature ( ) indicates general toughness, while the value at low temperature ( ) reveals how brittle the material becomes in cold environments (cold impact resistance).
- Heat Deflection Temperature (HDT) (ASTM D648)
- Description: The temperature at which the material deflects (bends) by a standard amount under a specific load (e.g., / or ).
- Importance: It determines the upper temperature limit at which a part can operate under mechanical load.
- Flammability / Flammability Rating (UL94)
- Description: A standard established by Underwriters Laboratories that classifies the flame-out time and drip behavior of plastic materials when exposed to a flame in a vertical or horizontal position (e.g., HB, V-2, V-1, V-0).
- Importance: It is a critical parameter for fire safety in the electrical/electronic and automotive industries.
2. What Are the Differences Between ASTM and ISO?
- ASTM (American Society for Testing and Materials): A North America-based standards organization. It is generally prioritized for projects and raw material specifications in the U.S. and the Americas.
- ISO (International Organization for Standardization): The International Organization for Standardization; it is the standard in European and Asian markets.
- Key Differences:
- Specimen Geometry: For the same test (e.g., tensile test), ASTM and ISO standards use test specimens of different dimensions (dumbbell/bone shape).
- Test Conditions and Rates: There may be minor methodological differences in tensile speed, test temperature tolerances, and pretreatment/conditioning requirements.
- Conclusion: Although ASTM and ISO test results for the same raw material are very close, they may not yield exactly the same numerical values due to differences in specimen geometry and test speed.
3. Other Common Values Found in Plastic Raw Material Specifications
Other important parameters you may frequently encounter in a technical data sheet include:
- Shore Hardness (Shore D or Shore A): Measures the resistance of elastomers and soft/hard plastics to surface scratching or indentation.
- Vicat Softening Temperature (ASTM D1525 / ISO 306): The temperature at which thermoplastics begin to soften when pierced with a needle (generally slightly higher than the HDT).
- Ash Content (%): Indicates, by gravimetric analysis, the proportion of non-combustible additives—such as minerals or glass fibers—present in the material.
- Water Absorption (%): The amount of water absorbed by the material over a specific period (e.g., 24 hours or until saturation is reached); this is particularly critical for dimensional stability in engineering plastics such as PA (polyamide).
- Coefficient of Linear Thermal Expansion (CLTE): Indicates how much the material will expand or contract dimensionally in response to temperature changes. It is of vital importance in mold design and tolerance calculations.
- The direct equivalents of STM test methods in international (ISO or IEC) standards are listed in the table below:
| Test Parameter |
ASTM Standard |
ISO / International Equivalent |
Description / Notes |
| Melt Flow Index (MFI) |
ASTM D1238 |
ISO 1133 |
Determination of melt flow rate. |
| Density |
ASTM D792 |
ISO 1183 |
Determination of density and specific gravity. |
| Tensile Stress (Yield) |
ASTM D638 |
ISO 527-2 |
Yield Strength (Tensile Properties). |
| Tensile Strain (Break) |
ASTM D638 |
ISO 527-2 |
Elongation at Break (Tensile Properties). |
| Flexural Modulus |
ASTM D790 |
ISO 178 |
Determination of flexural modulus / stiffness. |
| Notched Izod Impact (23°C / -10°C) |
ASTM D256 |
ISO 180 (or ISO 179) |
Notched Izod impact strength (ISO 179 is the Charpy impact standard; in specifications, the two are often used interchangeably). |
| Heat Deflection Temperature (HDT) |
ASTM D648 |
ISO 75-2 |
Heat Deflection Temperature (deflection under load). |
| Flammability |
UL94 |
IEC 60695-11-10 |
Flame behavior of plastic materials (Since UL94 is globally recognized, it is fully compatible with ISO/IEC test methods). |
The Tensile Stress (Yield Strength) and Flexural Modulus values listed in a plastic raw material’s technical data sheet are the two most critical parameters used to predict the material’s behavior under load in mechanical part design.
These values must be correctly interpreted in part design and incorporated into engineering calculations as follows:
1. How Should Tensile Stress at Yield Be Interpreted?
- What Does It Mean? It is the maximum tensile stress a material can withstand before undergoing permanent (plastic) deformation ( or ). Beyond this point, the material permanently elongates or loses its dimensional shape.
- Its Role in Part Design:
- Permanent Deformation Limit: The part you are designing (e.g., a clip, shaft, or body subjected to tensile force) must remain below this stress value during operation.
- Safety Factor (SF): Plastics are viscoelastic materials; that is, they are sensitive to time, temperature, and sustained load (creep). For this reason, the yield strength value listed in the datasheet is never taken directly as the maximum operating stress. Depending on the application, the allowable stress is calculated by applying a safety factor typically ranging from to .
- Example: For a PP or ABS material with a yield strength of , the continuous operating stress should not exceed the levels to remain on the safe side.
2. How Should the Flexural Modulus Be Interpreted?
- What Does It Mean? It indicates the material’s resistance to bending—that is, its stiffness (or modulus of elasticity) ( or ). The higher the value, the stiffer the material and the greater its resistance to bending.
- Role in Part Design:
- Deflection Control: It is used to calculate how much large-surface-area covers, panels, cantilevers, or beam-shaped parts will deflect when a load is applied. This value determines dimensional stability and aesthetic/functional deflection limits rather than strength.
- Beam and Rib Design: If you want your part to be sufficiently rigid, instead of excessively increasing the wall thickness (which leads to indentations and increased cost), you should select a material with a high flexural modulus or incorporate rib shapes appropriate for the part’s design.
3. Combined Use in Design and Critical Engineering Tips
- Strength vs. Stiffness Balance:
- Some materials may have high yield strength but be flexible (e.g., nylon derivatives). Others are very rigid (high flexural modulus) but brittle (e.g., glass-fiber-reinforced polymers). Whether a part will be subjected to impact or remain stationary while bearing a load is determined by the ratio of these two values.
- Anisotropy (Glass Fiber Effect):
- If the raw material you select is glass-fiber-reinforced (GF), the fibers align in the flow direction during injection. This causes the flexural modulus and tensile stress values in the flow direction to increase, while the values in directions perpendicular to the flow decrease. These directional differences must be taken into account in mold simulations (CAE).
- Temperature and Environmental Factors:
- Datasheet values are generally ideal results obtained at room temperature ( ) in a laboratory environment. At the operating temperature of your part (for example, in an engine compartment), both Tensile Stress and Flexural Modulus will experience significant decreases (softening). Decrease curves at the operating temperature must be taken into account in design calculations.

